>Minimus₂ and Minimus Lite digitisers. These can be recognised by
their serial numbers, which will be of the form
MINL-XXXX. For
digitisers with serial numbers of the form
MIN-XXXX, please see
the Release Notes for dig
Change log
2024/16/4 - Release 2.1-14470
This release contains the following fixes:
tunnel improvements
Logging improvements
Fixed console password reset of shorter string
2024/16/4 - Release 2.1-14176
This release contains the following fixes:
adc pre-amp gain now reflected in GDI metadata
Improvements to GPS tracking on loss of lock.
Fixed memory leak on triggers causing out of memory crash after 10,000 Events!
2024/01/17 - Release 2.1-13721
This release contains the following fixes:
STA/LTA trigger streams now ranged correctly
Fixed incorrect start timestamp on new files
Reduced memory useage so allowing full seedlink buffer
SD Card flush now writes partial miniseed blocks
Metadata channels now written more often to sd card
Maximum length Seedlink buffers now supported
NAM GDI loss of metadata on selective parameter update
Fixed crash in triggers when EEW params are calculated
Max GDI streams reduced to 1.
Issues with triggering on reboot fixed.
GPS robustness improved.
Future commands added.
Event table download triplet checkbox added.
General Certis improvements.
Improvements to system robustness.
Baidu Maps added as an option for the map on the web page.
2023/10/09 - Release 2.1-12649
This release contains the following fixes:
Improvements to NTP time.
Improvements to GPS tracking on loss of lock.
2023/09/14 - Release 2.1-12040
This release contains the following fixes:
Units modified in the "Edit Poles and Zeros" window in Discovery will now persist over reboots.
2023/09/13 - Release 2.1-12020
This release contains the following fixes:
Reduced time drift when GPS unit physically removed during operation.
The web page will now contain a warning when calibration is taking place.
HTTP port number can now be modified on the web page.
Various StationXML fixes.
Improvements to GPS timing robustness.
2023/08/29 - Release 2.1-11823
This release contains the following fixes:
The stationXML file for the Certis can now be found under Certis.xml
Improvements to the reporting for the Battery Pack.
2023/08/18 - Release 2.1-11561
This release contains the following fixes:
Certis full sample rates now available on digital connection
2023/08/11 - Release 2.1-11433
This release contains the following fixes:
Certis RESP/Dataless files now contain correct frequency response.
200 SPS now available for Certis.
GDI headers now legalised for older NAM compatibility
Channels relating to Certis can now be found under Certis in the Display on Page dropdown in Data Stream/Record.
Fixed possibility of gaps in data recorded to the SD cards.
A Full Format option now exists in the webpage to fully zero out all files.
Webpage now requires login to access all controls for digitiser.
Data will still be recorded to external SD card if internal SD card isn't functioning correctly.
Auxilliary files polezero.txt and calvals.txt are now functional for SCREAM compatibility.
Instrument Serial number now correctly stored when entered in the Poles and Zeros editor in discovery.
Download by time will now serve up to the most recent recorded data when future data is requested.
Warnings and checks added for SD cards of differing sizes
2023/06/29 - Release 2.1-10368
This release contains the following fixes:
The "Edit Poles and Zeros" page will now correctly disable enabled poles, zeros, or gains.
2023/06/29 - Release 2.1-10362
This release contains the following fixes:
Calibration Stream is now correctly expressed in Volts.
Peak ground values are now reported in discovery and the event table
STA/LTA streams now visible when using STA/LTA triggers
New low-power modes for guralp battery box
Tunneling has now been added to the Network tab
"Flush Data" button now works properly
Fixed incorrect labelling on the Storage tab buttons
Fixed downloads sometimes failing
More stability improvements
Added Uart Passthrough
Fixed modified SEED Names being reset on reboot
Copy to Data Stream/Record now copies SEED names as well as tap configuration
Apply configuration for tap groups now changes all corresponding sample rates when checked
Release 2.1-9734
This release contains the following fixes:
Fixed issue with Calibration Signal Generator
IP Address will now correctly show as DHCP instead of Static
Release 2.1-9653
This release contains the following fixes:
Fixed incorrect values on power channel
Corrected ≈1 ms timing offset
Fixed issue with units of "g" not showing up in Discovery when loading from a dataless file
Fixed custom units section in poles and zeros section of Discovery
Fixed incorrect filter coefficients in dataless seed files
General performance and stability improvements
Release 2.1-9039
This release contains the following fixes:
Added StationXML files to storage tab under Auxiliary files
Fixed errors with Triggering
Fixed errors when attempting to download by time
Calibration values from Certis will now be viewable in the calibration editor on newer versions of Discovery.
LED will now flash blue for five cycles upon a trigger.
event_table.txt now shows <1 second events as "<1" instead of 0 seconds.
Threshold triggers now identified correctly in event_table.txt.
Fixed date not showing correctly on system.log.
Release 2.1-8647
This release contains the following fixes:
Fixed custom channel units reseting on reboot.
Fixed issues with the threshold trigger on seismic channels.
Event Table text file (event_table.txt)
download can now be found the storage tab of the web page.
Added timestamps to system.log and fixed errors on some text editors.
Improvements to STA/LTA trigger performance.
2023-03-20 : release V2.1-7389
This release contains the following fixes:
SEED names are now delimited with periods; GCF stream names
remain hyphen-delimited.
Added more Platinum-compatible GDI metadata.
Release 2.1-6731
This release contains the following fix:
Added more Platinum-compatible GDI metadata.
Release 2.1-6633
This release contains the following fixes:
Removed extra sensors listed underneath Sensor Installation Parameters
Improved accuracy of Start data timestamp and Last data timestamp
Certis streams added to download by time dropdown
Duplicate seed names are now flagged correctly
Removed duplicate seed names from the default channels
Backfill now works across multiple files
Bluetooth reloading of firmware on boot fixed.
Extra DHCP request after failure on boot.
General bug fixes and improvements.
Release 2.1-6314
This release contains the following fixes:
Enabled Auto Reboot
Removed sensors status from the Status tab on the web page
Release 2.1-6309
This release contains the following fixes:
Improvements and fixes to timing accuracy
Added login support
System.log file is now available under Auxiliary files
Added some default calibration values
Added Channel data download by time selection
Added Download selected files
Fixed crash on password change
Fixed corruption of miniseed files
Release 2.1-5790
This release contains the following fixes:
Timing fixes
Release 2.1-5644
This release contains the following fixes:
Bluetooth now fully functional. This includes power-saving switches to allow LAN to be re-enabled
Start- and end-times of SD files now displayed on web page
Temperature and Humidity now shown of web page. GPS locking bug fixed
Data-download from web page supported. Dataless SEED generation added